General Infromation, interested parties to verify information

THIRD PARTY INFORMATION
-01-, The home owner should know Curb Valve location, it is one way the water supply can be turned off. Typically located public water main and house service, Municipal water department is responsible for the curb Valve functionality.
-02-, House service main begins at the curb valve and ends at the inside wall of building (master shut off valve)
-03-, The Master water shut off valve is where the service main enters the building. If the water meter is not inside the building, likely it will be in an underground casement (crock).
-04-, The water meter is normally the property of the municipal water company - usually located near the street.

-05-, Distribution Piping; Two important factors will be material used and age of material ie.
a/ Galvanized Piping, accumulates more mineral deposits than most other materials and is subject to rusting, in the event galvanized or steel piping are used, it is advised to consider replacing with a more friendly material.
b/ Brass Piping; life expectancy is estimated at approximately 40 - 70 years depending on the quality of brass material used.
c/ Copper Piping; has an approximate service life of 50 years, highly durable and not subject to mineral deposit clogging.
d/ Plastic Piping; (ABS,PEX, PB, PVC, PE, all different material some newer than others. When properly installed, supported and protected form sunlight and mechanical damage materials can/ may last indefinitely. (some different type fittings have proven unreliable resulting in several class action lawsuits.
e/ Lead Piping: used for water supply and distribution may be in older structures, MAY CAUSE HEALTH HAZARD TO OCCUPANTS.
TANK HOT WATER HEATER, will be either-Gas fired, Oil-fired
or electrically heated. Gas and Oil heater's life expectancy is approximately six to twelve years, both obtain a fairly high recovery rate. Electric heaters life expectancy is approx. five to ten years and has a lower recovery rate as gas and oil, which creates a necessity for the electric storage tank to be larger capacity. Leaking tanks are not normally repairable therefore require replacement when leaking.
PRIVATE WELL, There are 2 types of deep well pumps commonly used, one is Jet Pump-typically mounted above the well casing and two is the submersible pump located at the bottom of the well casing. the life expectancy of deep well pumps is approximately 10 years-submersible pumps are usually the most long lasting and trouble free of the two.
A well that provides drinking water will typically be located uphill from structures and septic systems.
Standards will require well to be minimum of 50 feet from septic tank and 100 feet from any absorption fields, different separation distances may occur subject to local codes and percolation rates of soils.
SEPTIC SYSTEM, A typical septic system life expectancy is approximately 15 to 20 years, periodic pumping should occur every tow to three years to help maintain long life.
T H A N K Y O U!

THIRD PARTY INFORMATION
-01-, The home owner should know Curb Valve location, it is one way the water supply can be turned off. Typically located public water main and house service, Municipal water department is responsible for the curb Valve functionality.
-02-, House service main begins at the curb valve and ends at the inside wall of building (master shut off valve)
-03-, The Master water shut off valve is where the service main enters the building. If the water meter is not inside the building, likely it will be in an underground casement (crock).
-04-, The water meter is normally the property of the municipal water company - usually located near the street.

-05-, Distribution Piping; Two important factors will be material used and age of material ie.
a/ Galvanized Piping, accumulates more mineral deposits than most other materials and is subject to rusting, in the event galvanized or steel piping are used, it is advised to consider replacing with a more friendly material.
b/ Brass Piping; life expectancy is estimated at approximately 40 - 70 years depending on the quality of brass material used.
c/ Copper Piping; has an approximate service life of 50 years, highly durable and not subject to mineral deposit clogging.
d/ Plastic Piping; (ABS,PEX, PB, PVC, PE, all different material some newer than others. When properly installed, supported and protected form sunlight and mechanical damage materials can/ may last indefinitely. (some different type fittings have proven unreliable resulting in several class action lawsuits.
e/ Lead Piping: used for water supply and distribution may be in older structures, MAY CAUSE HEALTH HAZARD TO OCCUPANTS.
TANK HOT WATER HEATER, will be either-Gas fired, Oil-fired
or electrically heated. Gas and Oil heater's life expectancy is approximately six to twelve years, both obtain a fairly high recovery rate. Electric heaters life expectancy is approx. five to ten years and has a lower recovery rate as gas and oil, which creates a necessity for the electric storage tank to be larger capacity. Leaking tanks are not normally repairable therefore require replacement when leaking.
PRIVATE WELL, There are 2 types of deep well pumps commonly used, one is Jet Pump-typically mounted above the well casing and two is the submersible pump located at the bottom of the well casing. the life expectancy of deep well pumps is approximately 10 years-submersible pumps are usually the most long lasting and trouble free of the two.
A well that provides drinking water will typically be located uphill from structures and septic systems.
Standards will require well to be minimum of 50 feet from septic tank and 100 feet from any absorption fields, different separation distances may occur subject to local codes and percolation rates of soils.
SEPTIC SYSTEM, A typical septic system life expectancy is approximately 15 to 20 years, periodic pumping should occur every tow to three years to help maintain long life.
T H A N K Y O U!

THIRD PARTY INFORMATION
-01-, The home owner should know Curb Valve location, it is one way the water supply can be turned off. Typically located public water main and house service, Municipal water department is responsible for the curb Valve functionality.
-02-, House service main begins at the curb valve and ends at the inside wall of building (master shut off valve)
-03-, The Master water shut off valve is where the service main enters the building. If the water meter is not inside the building, likely it will be in an underground casement (crock).
-04-, The water meter is normally the property of the municipal water company - usually located near the street.

-05-, Distribution Piping; Two important factors will be material used and age of material ie.
a/ Galvanized Piping, accumulates more mineral deposits than most other materials and is subject to rusting, in the event galvanized or steel piping are used, it is advised to consider replacing with a more friendly material.
b/ Brass Piping; life expectancy is estimated at approximately 40 - 70 years depending on the quality of brass material used.
c/ Copper Piping; has an approximate service life of 50 years, highly durable and not subject to mineral deposit clogging.
d/ Plastic Piping; (ABS,PEX, PB, PVC, PE, all different material some newer than others. When properly installed, supported and protected form sunlight and mechanical damage materials can/ may last indefinitely. (some different type fittings have proven unreliable resulting in several class action lawsuits.
e/ Lead Piping: used for water supply and distribution may be in older structures, MAY CAUSE HEALTH HAZARD TO OCCUPANTS.
TANK HOT WATER HEATER, will be either-Gas fired, Oil-fired
or electrically heated. Gas and Oil heater's life expectancy is approximately six to twelve years, both obtain a fairly high recovery rate. Electric heaters life expectancy is approx. five to ten years and has a lower recovery rate as gas and oil, which creates a necessity for the electric storage tank to be larger capacity. Leaking tanks are not normally repairable therefore require replacement when leaking.
PRIVATE WELL, There are 2 types of deep well pumps commonly used, one is Jet Pump-typically mounted above the well casing and two is the submersible pump located at the bottom of the well casing. the life expectancy of deep well pumps is approximately 10 years-submersible pumps are usually the most long lasting and trouble free of the two.
A well that provides drinking water will typically be located uphill from structures and septic systems.
Standards will require well to be minimum of 50 feet from septic tank and 100 feet from any absorption fields, different separation distances may occur subject to local codes and percolation rates of soils.
SEPTIC SYSTEM, A typical septic system life expectancy is approximately 15 to 20 years, periodic pumping should occur every tow to three years to help maintain long life.
T H A N K Y O U!

THIRD PARTY INFORMATION
-01-, The home owner should know Curb Valve location, it is one way the water supply can be turned off. Typically located public water main and house service, Municipal water department is responsible for the curb Valve functionality.
-02-, House service main begins at the curb valve and ends at the inside wall of building (master shut off valve)
-03-, The Master water shut off valve is where the service main enters the building. If the water meter is not inside the building, likely it will be in an underground casement (crock).
-04-, The water meter is normally the property of the municipal water company - usually located near the street.

-05-, Distribution Piping; Two important factors will be material used and age of material ie.
a/ Galvanized Piping, accumulates more mineral deposits than most other materials and is subject to rusting, in the event galvanized or steel piping are used, it is advised to consider replacing with a more friendly material.
b/ Brass Piping; life expectancy is estimated at approximately 40 - 70 years depending on the quality of brass material used.
c/ Copper Piping; has an approximate service life of 50 years, highly durable and not subject to mineral deposit clogging.
d/ Plastic Piping; (ABS,PEX, PB, PVC, PE, all different material some newer than others. When properly installed, supported and protected form sunlight and mechanical damage materials can/ may last indefinitely. (some different type fittings have proven unreliable resulting in several class action lawsuits.
e/ Lead Piping: used for water supply and distribution may be in older structures, MAY CAUSE HEALTH HAZARD TO OCCUPANTS.
TANK HOT WATER HEATER, will be either-Gas fired, Oil-fired
or electrically heated. Gas and Oil heater's life expectancy is approximately six to twelve years, both obtain a fairly high recovery rate. Electric heaters life expectancy is approx. five to ten years and has a lower recovery rate as gas and oil, which creates a necessity for the electric storage tank to be larger capacity. Leaking tanks are not normally repairable therefore require replacement when leaking.
PRIVATE WELL, There are 2 types of deep well pumps commonly used, one is Jet Pump-typically mounted above the well casing and two is the submersible pump located at the bottom of the well casing. the life expectancy of deep well pumps is approximately 10 years-submersible pumps are usually the most long lasting and trouble free of the two.
A well that provides drinking water will typically be located uphill from structures and septic systems.
Standards will require well to be minimum of 50 feet from septic tank and 100 feet from any absorption fields, different separation distances may occur subject to local codes and percolation rates of soils.
SEPTIC SYSTEM, A typical septic system life expectancy is approximately 15 to 20 years, periodic pumping should occur every tow to three years to help maintain long life.
T H A N K Y O U!

THIRD PARTY INFORMATION
-01-, The home owner should know Curb Valve location, it is one way the water supply can be turned off. Typically located public water main and house service, Municipal water department is responsible for the curb Valve functionality.
-02-, House service main begins at the curb valve and ends at the inside wall of building (master shut off valve)
-03-, The Master water shut off valve is where the service main enters the building. If the water meter is not inside the building, likely it will be in an underground casement (crock).
-04-, The water meter is normally the property of the municipal water company - usually located near the street.

-05-, Distribution Piping; Two important factors will be material used and age of material ie.
a/ Galvanized Piping, accumulates more mineral deposits than most other materials and is subject to rusting, in the event galvanized or steel piping are used, it is advised to consider replacing with a more friendly material.
b/ Brass Piping; life expectancy is estimated at approximately 40 - 70 years depending on the quality of brass material used.
c/ Copper Piping; has an approximate service life of 50 years, highly durable and not subject to mineral deposit clogging.
d/ Plastic Piping; (ABS,PEX, PB, PVC, PE, all different material some newer than others. When properly installed, supported and protected form sunlight and mechanical damage materials can/ may last indefinitely. (some different type fittings have proven unreliable resulting in several class action lawsuits.
e/ Lead Piping: used for water supply and distribution may be in older structures, MAY CAUSE HEALTH HAZARD TO OCCUPANTS.
TANK HOT WATER HEATER, will be either-Gas fired, Oil-fired
or electrically heated. Gas and Oil heater's life expectancy is approximately six to twelve years, both obtain a fairly high recovery rate. Electric heaters life expectancy is approx. five to ten years and has a lower recovery rate as gas and oil, which creates a necessity for the electric storage tank to be larger capacity. Leaking tanks are not normally repairable therefore require replacement when leaking.
PRIVATE WELL, There are 2 types of deep well pumps commonly used, one is Jet Pump-typically mounted above the well casing and two is the submersible pump located at the bottom of the well casing. the life expectancy of deep well pumps is approximately 10 years-submersible pumps are usually the most long lasting and trouble free of the two.
A well that provides drinking water will typically be located uphill from structures and septic systems.
Standards will require well to be minimum of 50 feet from septic tank and 100 feet from any absorption fields, different separation distances may occur subject to local codes and percolation rates of soils.
SEPTIC SYSTEM, A typical septic system life expectancy is approximately 15 to 20 years, periodic pumping should occur every tow to three years to help maintain long life.
T H A N K Y O U!

THIRD PARTY INFORMATION
-01-, The home owner should know Curb Valve location, it is one way the water supply can be turned off. Typically located public water main and house service, Municipal water department is responsible for the curb Valve functionality.
-02-, House service main begins at the curb valve and ends at the inside wall of building (master shut off valve)
-03-, The Master water shut off valve is where the service main enters the building. If the water meter is not inside the building, likely it will be in an underground casement (crock).
-04-, The water meter is normally the property of the municipal water company - usually located near the street.

-05-, Distribution Piping; Two important factors will be material used and age of material ie.
a/ Galvanized Piping, accumulates more mineral deposits than most other materials and is subject to rusting, in the event galvanized or steel piping are used, it is advised to consider replacing with a more friendly material.
b/ Brass Piping; life expectancy is estimated at approximately 40 - 70 years depending on the quality of brass material used.
c/ Copper Piping; has an approximate service life of 50 years, highly durable and not subject to mineral deposit clogging.
d/ Plastic Piping; (ABS,PEX, PB, PVC, PE, all different material some newer than others. When properly installed, supported and protected form sunlight and mechanical damage materials can/ may last indefinitely. (some different type fittings have proven unreliable resulting in several class action lawsuits.
e/ Lead Piping: used for water supply and distribution may be in older structures, MAY CAUSE HEALTH HAZARD TO OCCUPANTS.
TANK HOT WATER HEATER, will be either-Gas fired, Oil-fired
or electrically heated. Gas and Oil heater's life expectancy is approximately six to twelve years, both obtain a fairly high recovery rate. Electric heaters life expectancy is approx. five to ten years and has a lower recovery rate as gas and oil, which creates a necessity for the electric storage tank to be larger capacity. Leaking tanks are not normally repairable therefore require replacement when leaking.
PRIVATE WELL, There are 2 types of deep well pumps commonly used, one is Jet Pump-typically mounted above the well casing and two is the submersible pump located at the bottom of the well casing. the life expectancy of deep well pumps is approximately 10 years-submersible pumps are usually the most long lasting and trouble free of the two.
A well that provides drinking water will typically be located uphill from structures and septic systems.
Standards will require well to be minimum of 50 feet from septic tank and 100 feet from any absorption fields, different separation distances may occur subject to local codes and percolation rates of soils.
SEPTIC SYSTEM, A typical septic system life expectancy is approximately 15 to 20 years, periodic pumping should occur every tow to three years to help maintain long life.
T H A N K Y O U!



You must be logged in to add a comment to this message.
Click Here to Login